02 sensor

speedmachine · Post by **speedmachine** » Thu Mar 09, 2006 1:52 pm

Can anyone tell me

which is the best way to disconnect the O2 sensor i.e.

(1), from the (y) peace.

(2) or from the connector under the fuel tank.

Which way and why.
Thanks speedmachine

sandbar · Post by **sandbar** » Thu Mar 09, 2006 2:04 pm

You can't disconnect it at the Y-piece. Well you could - by cutting the wires

All you can do at the y-piece is to unscrew it and replace it with a suitable bolt.

Under the tank is my preferred option.

sandbar

boxerpan · Post by **boxerpan** » Thu Mar 09, 2006 2:09 pm

Under tank - off side of bike

bigblackfalco · Post by **bigblackfalco** » Thu Mar 09, 2006 4:43 pm

My advice from previous experience,leave the sensor in(often gets heat welded/rusted in and may shear!Also bolts tend to rattle loose from the vibration) and connector disconnect under tank.
Bailey.

iandunn1100ss · Post by **iandunn1100ss** » Thu Mar 09, 2006 4:57 pm

Can i ask what gains will come from this mod?

speedmachine · Post by **speedmachine** » Thu Mar 09, 2006 5:56 pm

The reason I asked, because I run my bike with 02 sensor disconnected
At the (y)peace put Bolt in its place.

The bike was running spot-on before .
After talking to Darren at motoworks, about the fuel pressure regulator.
I explain to him where I had disconnected o2 sensor is reply was.
To disconnected from underneath tank so while fitted fuel pressu,
regulator I had decided to disconnect o2 sensor from underneath the tank.
Which I did but after disappointing result with regulator I swapped regulator back over but left the O2 sensor disconnected.
The bike still doesn't feel as good as it did before

.
So, I was wondering if that is because of the O2 sensor

speedmachine · Post by **speedmachine** » Thu Mar 09, 2006 6:34 pm

Do not know. That's why I'm asking

Boxadog 2000 · Post by **Boxadog 2000** » Thu Mar 09, 2006 7:15 pm

Disconnect O2 sensor and bike runs on base IE default map like crap

speedmachine · Post by **speedmachine** » Mon Mar 13, 2006 1:43 pm

Re fitted O2 sensor at the connector under tank.
What are pain to get to

then unscrewed it at the y peace screwed bolt in place .
That used tie rap to old sensor in place on the y peace.
Hopefully, the bike will run better
but too cold to test bike.

Me-109 · Post by **Me-109** » Mon Mar 13, 2006 10:28 pm

So you've reconnected the O2 sensor but left it hanging in the breeze? Wouldn't it do better being screwed in?

speedmachine · Post by **speedmachine** » Tue Mar 14, 2006 9:12 am

No not really.
I do believe the O2 sensor, is there to protect the catalytic converter.
But not haven't the catalytic converter in Its place is no longer needed. I have run the bike like this before for about 5 months.
The bike runs a lot better in lower revs see smoother

sandbar · Post by **sandbar** » Tue Mar 14, 2006 9:39 am

I'm confused!!!

So what's new? - I hear!

I thought the O2 sensor only worked at low revs AND at low throttle openings. Under those conditions it measured the exhaust gases and tried (if necessary) to persuade the ECU to get as close as possible to a theoretical perfect emmission situation. That would indeed have the secondary effect of protecting the catalytic converter. But it also has another effect apparently ( particularly on R1150RT) of causing surging.

But surely, other than under those circumstances, it cannot alter whatever map is currently in use?

The only way to alter the map ( other than changing the chip - obviously) is to remove or change the cat code plug. Removing it gets to the default (rich) map!!

Incidentally mine runs smoothest with cat code removed, O2 sensor disconnected and 1200GS regulator. That applies whether on standard exhaust (with cat) or Laser (road) system with baffles removed.

sandbar

bigblackfalco · Post by **bigblackfalco** » Tue Mar 14, 2006 10:31 am

speedmachine wrote:No not really.
I do believe the O2 sensor, is there to protect the catalytic converter.
But not haven't the catalytic converter in Its place is no longer needed. I have run the bike like this before for about 5 months.
The bike runs a lot better in lower revs see smoother

If the O2 sensor is connected,then it should screwed in the Y piece....other wise it will be reading the CO contents of the atmosphere!
Bailey.

speedmachine · Post by **speedmachine** » Tue Mar 14, 2006 11:01 am

When I first put the chip in the bike.
When riding in town, the bike was quite jerky.
Up to about 20 mph. Also backfired, quite a lot.
With d accelerated quite bad vibration.

When reading post on a forum about disconnected O2 sensor.
I decided to disconnect my not realising that most people disconnected it.
From under tank. I just unscrewed it at the y peace put Bolt in place.
Just tie rap O2 sensor to a section of the exhaust .
On The first ride out bike fell smoother in traffic. there was no backfiring and less vibration..

I ham no mechanic but I could tell straight away. The bike was running better.
When you talk about surges. I haven quite sure what this mean

I have been riding for 20 years, I am quite confident I could tell.
Whether the bike is running good or bad.
Go easy on me please.

speedmachine · Post by **speedmachine** » Tue Mar 14, 2006 11:16 am

May be reading air

www.boxertrix.com

02 sensor

02 sensor

Refitted