www.boxertrix.com

Is it Pro-Care No 1?

Al

I'm thinking of using a paint spraying kit and a small air compressor-that should be easy enough to get the desired misting effect shouldn't it??

I spoke to the guys at nippy Normans who agreed that the aerosol does give a big thick splurge of ACF but if I buy the litre it came with a pump bottle which is "slightly" better! I think I'll give the 1L a go and if the pump bottle isn't any better I can look at other alternatives!!

ACF50 seems to spray better if you have slightly warmed it. I usually leave the can on top of the central heating radiator for 1/2 hour whilst cleaning the bike.

Don't over pump the ACF bottle, if the pressure is too high you get a jet, rather than a mist.

I spray it on then spread it with a designated ACF rag.

It's probabley more use on your winter hack than the S though.....

Steve1200S wrote:Don't over pump the ACF bottle, if the pressure is too high you get a jet, rather than a mist.

I spray it on then spread it with a designated ACF rag.

It's probabley more use on your winter hack than the S though.....

Agree with the above.The ACF bottle spray is good for touch up through winter once you've warmed it.

It's about now that I remove the plastics from my RT and get the cheapo paint spray gun I bought and the compressor out and use that to apply the ACF, it's a far better way of doing it as it really does atomise the ACF and allow it to get everywhere you can get to and doesn't over apply it.

ACF50 specific rag and a paint brush is good for top up through winter.
I tend to still hose off with COLD water after riding on salty roads mind, just not a proper clean as I don't want to remove the ACF.

Proper clean and a recaoat with ACF come Christmas
\v/

I'm tempted to shut up and just buy ACF50 shares........

If you are spraying it on - what the hell are you spraying it on to?

It sounds like you have found acres of untreated aluminium or magnesium on your bikes

Get a can of a hard cavity wax and spray it over the rest of the bike, using the ACF50 for bare bolts etc.......

You won't have to worry about destroying the cavity wax film with washing - in fact you'll need to go some to get rid of it


Al

It's the creepbilty of the Acf. I prefer, ease of application and removal. When the time comes.
And it works.
The OP asked about Acf application., just giving my methods of using it.
\v/

Clean bike to within an inch of it's life.

Remove body work & wheels mask of calipers.

Put regular aerosol can in ho water and keep a jug of hot water handy to keep the can warm


Mask off discs and spray ACF50 onto a small paint brush and paint wheels and spokes.

Re install wheels and then clean brake discs with brake cleaner.

Ride bike all through winter do not bother to wash at all.

End of February clean bike twice with S Doc 100 gel cleaner, polish hey presto bike looks like it just came out of the showroom ( ask other folks about the condition of my bikes)

Remember keep the can warm at all times a regular aerosol can is more than enough to do a bike well

One decent coat is enough to last all winter.

Takes me about 4 hours to do my GS Adventure start to finish

with you on this Al, I used some waxoyl type stuff years ago on an R65 - ran it all winter and cleaned it off and the bike looked like new - was a bugger to clean off mind!!

took me a while ,,, the really good thick scented wd40 stuff that works so well ,was called ,,,,,, break away. plain steel gallon tin yellow label from the motor factors , perfumed smell.
hope that helps some one

Blackal wrote: Then get a leaf-blower and dry it off, paying particular attention to the brake calipers.

If you are storing it for 4+ months - take the brake pads out not a huge job) as it will save the galvanic action between the bronze flecks in the pads and the steel of the discs. They can pit a disc really badly over the winter.

(Don't forget to refit them in Feb )

Good idea 'bout brake pads. That galvanic action; Ugh After getting caught out late one night a week or so ago on freshly salted roads, I washed my bike, dried it off as best I could (no leaf blower tho ) and put it away. Took the cover off yesterday to see if things were 'ok' and wadyano Could'nt rotate the front wheel 'cos the pads had stuck (rusted) to the rotors I've got to use it over the holiday but next time I lay it up I'll be removing the bolts and moving the calipers to the very edge of the disc. That way the pads won't 'creep' together and the discs won't get pitted. I'll shove the workshop broom handle thru the front wheel to remind me to refit them .

el-nicko wrote:

Blackal wrote: Then get a leaf-blower and dry it off, paying particular attention to the brake calipers.

If you are storing it for 4+ months - take the brake pads out not a huge job) as it will save the galvanic action between the bronze flecks in the pads and the steel of the discs. They can pit a disc really badly over the winter.

(Don't forget to refit them in Feb )

Good idea 'bout brake pads. That galvanic action; Ugh After getting caught out late one night a week or so ago on freshly salted roads, I washed my bike, dried it off as best I could (no leaf blower tho ) and put it away. Took the cover off yesterday to see if things were 'ok' and wadyano Could'nt rotate the front wheel 'cos the pads had stuck (rusted) to the rotors I've got to use it over the holiday but next time I lay it up I'll be removing the bolts and moving the calipers to the very edge of the disc. That way the pads won't 'creep' together and the discs won't get pitted. I'll shove the workshop broom handle thru the front wheel to remind me to refit them .

A piece of plastic oil container between the pads and disc's will do the job

I use fs365, summer and winter. Doddle to use, spray on when bike is wet, either after a wash, or after a wet ride. Job done.

Dai wiskers wrote: A piece of plastic oil container between the pads and disc's will do the job

I'll give that a try too m8.

el-nicko wrote:

Dai wiskers wrote: A piece of plastic oil container between the pads and disc's will do the job

seriously? Oil container?
I'd go with a piece of plastic milk carton myself.

Steve