R12S Torque values

[victorlaszlo]

Doing service tomorrow but have misplaced the table of torque values, anyone who can help completing the below?

Oil drain plug torque 32 Nm (is this for engine oil?)
Oil filter 11 Nm on the filter.
Oil filler plug
Oil gear filler plug
Oil gear drain plug

Front brake calliper 30 Nm
From brake grub screw 7 Nm
Front brake calliper bleed screw 5 Nm

Rear brake calliper 24 Nm
Rear brake calliper bleed screw 5 Nm

Wheel quick release axle in axle holder 50 Nm
Wheel quick release axle clamp screws 19 Nm
Wheel rear bolts 60 Nm

Final drive cover to final drive housing (m8x30) 30 Nm
Final drive oil filler plug in final drive housing (with O-ring 11.2x1.8, without M12x1) 20 Nm
Paralever reaction link to final drive housing 42 Nm (replace nut)
Paralever reaction link to frame 42 Nm (replace screws)

Cyl head cover to cyl head M6 x 72mm, tighten diagonally in sequence to a final torque of 10Nm
Valve lock nuts
Spark plugs

In bold missing values, anything additional would be great!

[milleplod]

Doing service tomorrow but have misplaced the table of torque values, anyone who can help completing the below?

Oil drain plug torque 32 Nm (is this for engine oil?).....service CD-ROM says 23Nm, then 32Nm
Oil filter 11 Nm on the filter.
Oil filler plug - I've never torqued this, just done it by hand, nice and tight!
Oil gear filler plug 30Nm
Oil gear drain plug 30Nm

Front brake calliper 30 Nm
From brake grub screw 7 Nm
Front brake calliper bleed screw 5 Nm

Rear brake calliper 24 Nm
Rear brake calliper bleed screw 5 Nm

Wheel quick release axle in axle holder 50 Nm
Wheel quick release axle clamp screws 19 Nm
Wheel rear bolts 60 Nm

Final drive cover to final drive housing (m8x30) 30 Nm
Final drive oil filler plug in final drive housing (with O-ring 11.2x1.8, without M12x1) 20 Nm
Paralever reaction link to final drive housing 42 Nm (replace nut)
Paralever reaction link to frame 42 Nm (replace screws)

Cyl head cover to cyl head M6 x 72mm, tighten diagonally in sequence to a final torque of 10Nm
[b]Valve lock nuts 8Nm
Spark plugs 23Nm

In bold missing values, anything additional would be great!

Hope that helps!

Pete

[victorlaszlo]

Hope that helps!

Pete

Awesome, cheers!

[victorlaszlo]

Update:

Oil drain plug torque initial torque 23 Nm, then 32 Nm
Oil filter 11 Nm on the filter
Oil gear filler plug 30 Nm
Oil gear drain plug 30 Nm

Front brake calliper 30 Nm
From brake grub screw 7 Nm
Front brake calliper bleed screw 5 Nm

Rear brake calliper 24 Nm
Rear brake calliper bleed screw 5 Nm

Wheel quick release axle in axle holder 50 Nm
Wheel quick release axle clamp screws 19 Nm
Wheel rear bolts 60 Nm

Final drive cover to final drive housing (m8x30) 30 Nm
Final drive oil filler plug in final drive housing (with O-ring 11.2x1.8, without M12x1) 20 Nm
Paralever reaction link to final drive housing 42 Nm (replace nut)
Paralever reaction link to frame 42 Nm (replace screws)

Cyl head cover to cyl head M6 x 72mm, tighten diagonally in sequence to a final torque of 10 Nm
Valve lock nuts 8 Nm
Spark plugs 23 Nm

I'm more than happy for any additional useful values to be added, I'll save this page as a reference!